Quantum states in fabricating poly-Si films

The quantum states are presented in these processions of fabricating poly-Si films. Amorphous silicon films prepared by PECVD has been crystallized by conventional furnace annealing (FA) and rapid thermal annealing (RTA), respectively. It is found that the thin films grain size present quantum states with the increasing of the gas flow ratios of SiH₄, H₂ mixture, substrate temperatures, frequency power, annealing temperature and time.     

Preparation of rhodium–phyllosilicate catalysts without leaching in liquid-phase 1-hexene hydrogenation

Rhodium catalysts have been prepared on palygorskite and montmorillonite (clay) supports by reduction with hydrogen (1 atmosphere) at room temperature of a cationic organometallic rhodium compound anchored to the support. The activity of these catalysts for the hydrogenation of liquid-phase 1-hexene remains constant with increase of prehydrogenation time and with re-use for several runs. No rhodium leaching is observed.     

Metallo‐supramolecular block copolymer micelles: Improved preparation and characterization

Micelles prepared from amphiphilic block copolymers in which a poly(styrene) segment is connected to a poly(ethylene oxide) block via a bis‐(2,2′:6′,2″‐terpyridine‐ruthenium) complex have been intensely studied. In most cases, the micelle populations were found to be strongly heterogeneous in size because of massive micelle/micelle aggregation. In the study reported in this article we tried to improve the homogeneity of the micelle population. The variant preparation procedure developed, which is described here, was used to prepare two “protomer”‐type micelles: PS₂₀‐[Ru]‐PEO₇₀ and PS₂₀‐[Ru]‐PEO₃₇₅. The dropwise addition of water to a solution of the compounds in dimethylformamide was replaced by the controlled addition of water by a syringe pump. The resulting micelles were characterized by sedimentation velocity and sedimentation equilibrium analyses in an analytical ultracentrifuge and by transmission electron microscopy of negatively stained samples. Sedimentation analysis showed virtually unimodal size distributions, in contrast to the findings on micelles prepared previously. PS₂₀‐[Ru]‐PEO₇₀ micelles were found to have an average molar mass of 318,000 g/mol (corresponding to 53 protomers per micelle, which is distinctly less than after micelle preparation by the standard method) and an average hydrodynamic diameter (d_h) of 18 nm. For PS₂₀‐[Ru]‐PEO₃₇₅ micelles, the corresponding values were M = 603,000 g/mol (31 protomers per micelle) and d_h = 34 nm. The latter particles were found to be identical to the “equilibrium” micelles prepared in pure water. Both micelle types had a very narrow molar mass distribution but a much broader distribution of s values and thus of hydrodynamic diameters. This indicates a conformational heterogeneity that is stable on the time scale of sedimentation velocity analysis. The findings from electron microscopy were in disagreement with those from the sedimentation analysis both in average micelle diameter and in the width of the distributions, apparently because of imperfections in the staining procedure. The preparation procedure described also may be useful in micelle formation from other types of protomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4458–4465, 2004     

Über die Magnetischen Eigenschaften der Cobaltate Na6CoS4, Na6CoSe4 und K6CoS4

Magnetic Properties of the Cobaltates Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ The alkali metal cobalt chalcogenides Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ crystallize in the space group P6₃mc with Z = 4. The structure is characterized by isolated [CoX₄]-tetrahedra. The magnetic susceptibilities show Curie-Weiss behaviour. The deviations at low temperatures are caused by antiferromagnetic interactions. The magnetic moments are discussed with regard to ligand-field parameters.     

Proteinases from Carica papaya Latex

Data on the proteinase complex from Carica papaya latex were reviewed. The properties and applications of the domestic preparation cucumazyme and known medicinal preparations based on papaya proteinases (caripazyme, lecozyme, lecopain) were compared.     

免疫珠技术快速检测腹泻性大肠杆菌

采用表面光滑玻璃珠作为载体材料，用1：40的腹泻性大肠杆菌诊断血清进行包被。可制成免疫珠。这种免疫珠能与腹泻性大肠杆菌发生特异性结合。经乳糖蛋白胨培养液培养，然后根据其产酸产气进行判断。能在18h内完成腹泻性大肠杆菌的检测。其灵敏度为样液中含有腹泻性大肠杆菌数必须大于10CFu／mL．该法简单、快速、易操作、灵敏度高。     

Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.     

Investigating laser rapid manufacturing for Inconel-625 components

This paper presents an investigation of laser rapid manufacturing (LRM) for Inconel-625 components. LRM is an upcoming rapid manufacturing technology, it is similar to laser cladding at process level with different end applications. In general, laser-cladding technique is used to deposit materials on the substrate either to improve the surface properties or to refurbish the worn out parts, while LRM is capable of near-net shaping the components by layer-by-layer deposition of the material directly from CAD model. In the present study, a high-power continuous wave (CW) CO₂ laser system, integrated with a co-axial powder-feeding system and a three-axis workstation were used. The effect of processing parameters during LRM of Inconel-625 was studied and the optimum set of parameters for the maximum deposition rate was established employing Orthogonal L9 array of Taguchi technique. Results indicated that the powder feed rate and the scan speed contributed about 56% and 26%, respectively to the deposition rate, while the influence of laser power was limited to 10% only. Fabricated components were subjected to non-destructive testing (like—ultrasonic testing, dye-penetrant testing), tensile testing, impact testing, metallographic examinations and micro-hardness measurement. The test results revealed defect-free material deposition with improved mechanical strength without sacrificing the ductility.     

Zur Synthese von Bor-Schwefel(IV)-Stickstoff-Heterocyclen

Synthesis of Boron-Sulfur(IV)-Nitrogen Heterocycles The reaction of bis(lithio.tert.-butylamino)phenylborane with tert.-butyldichlorosulfimide and bischlorodimethylsilylsulfodiimide respectively leads to four- or eight-membered heterocycles. The disulfanebridge of one dithiazadiborolidine can be replaced by the ? N?S?N-sequence to yield a Thiatriazadiborine. ¹H, ¹¹B, ¹³C-NMR, mass spectra, and analytical data are reported and discussed.     

Specific heat and related thermophysical properties of liquid Fe-Cu-Mo alloy

The specific heat and related thermophysical properties of liquid Fe77.5Cu13Mo9.5 monotectic alloy were investigated by an electromagnetic levitation drop calorimeter over a wide temperature range from 1482 to 1818 K. A maximum undercooling of 221 K (0.13 Tm) was achieved and the specific heat was determined as 44.71 J·mol-1·K-1. The excess specific heat, enthalpy change, entropy change and Gibbs free energy difference of this alloy were calculated on the basis of experimental results. It was found that the calculated results by traditional estimating methods can only describe the solidification process under low undercooling conditions. Only the experimental results can reflect the reality under high undercooling conditions. Meanwhile, the thermal diffusivity, thermal conductivity, and sound speed were derived from the present experimental results. Furthermore, the solidified microstructural morphology was examined, which consists of (Fe) and (Cu) phases. The calculated interface energy was applied to exploring the correlation between competitive nucleation and solidification microstructure within monotectic alloy.